Philco 38-62 cabinet restoration
Posts: 803
Threads: 42
Joined: Dec 2008
City: Chicago, IL
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Boy that did clean up really nice!!
Terry
Posts: 4,806
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
What sort of bleach did you use, was it just the common sodium hypochlorate bleach like you find under the kitchen sink? I've found that you can get rid of the black stains in some woods with phosphoric acid, which leads me to think that they are iron stains.
Regards
Arran
Posts: 803
Threads: 42
Joined: Dec 2008
City: Chicago, IL
Just common bleach. I think it was water stains and mildew on this cabinet.
(This post was last modified: 04-12-2013, 01:12 PM by Bob Andersen.)
Posts: 803
Threads: 42
Joined: Dec 2008
City: Chicago, IL
Time for grain filler. I used Constantines thinned a little with mineral spirits. After it dried to a haze, I scraped off the excess with a credit card.
It's a bit too light in the middle of the top from the bleaching. I hope to blend that out with toner.
[Image: http://farm9.staticflickr.com/8536/86437...ef8a_c.jpg]
[Image: http://farm9.staticflickr.com/8245/86426...781b_c.jpg]
(This post was last modified: 04-12-2013, 02:38 PM by Bob Andersen.)
Posts: 163
Threads: 8
Joined: Jun 2011
City: Chicago,illinois
Bob...it's getting there. Nice work!
Posts: 803
Threads: 42
Joined: Dec 2008
City: Chicago, IL
Thanks. I just sprayed on some sanding sealing and a few coats of Medium Brown Walnut toner lacquer.
I thought it looked pretty good, but now that I've compared it to the original photos I think it's a little too light 
[Image: http://farm9.staticflickr.com/8254/86525...e798_c.jpg]
(This post was last modified: 04-15-2013, 06:04 PM by Bob Andersen.)
Posts: 4,806
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
I thought that they may have used something close to extra dark walnut toner like the 1936 Philco tombstones used, it looks like they used a similar junk wood for the top and sides of the cabinet. Maybe it was perfect brown toner?
Regards
Arran
(This post was last modified: 04-15-2013, 08:10 PM by Arran.)
Posts: 803
Threads: 42
Joined: Dec 2008
City: Chicago, IL
The traces of original finish left weren't quite so dark or opaque as my mid-30s tombstones. I do have some dye based extra dark walnut lacquer though and I'll give it a try tomorrow.
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
Starting to look pretty super there Dynamo Bob!!!
GREAT JOB!!
Terry
Posts: 803
Threads: 42
Joined: Dec 2008
City: Chicago, IL
Thanks Terry and good call Arran. The extra dark walnut looks much better  It's a rich, dark brown and you can still see hints of the grain. That just leaves the trim.
[Image: http://farm9.staticflickr.com/8122/86560...9927_c.jpg]
(This post was last modified: 04-16-2013, 02:14 PM by Bob Andersen.)
Posts: 163
Threads: 8
Joined: Jun 2011
City: Chicago,illinois
WOW...That's looking great! Can't wait to see it done.
Posts: 5,125
Threads: 271
Joined: Nov 2012
City: Wilsonville
State, Province, Country: OR
wow! very nice 
Posts: 803
Threads: 42
Joined: Dec 2008
City: Chicago, IL
I wrapped up the toner and put on a couple coats of clear gloss this afternoon. I knew I was taking a chance because of the high humidity levels, but I really wanted to get it done.
Luckily, just a minimal amount of blushing in the clear coat that I expect will sand out.
[Image: http://farm9.staticflickr.com/8265/86618...9143_c.jpg]
The scar where I repaired the split is barely visible in very bright light.
[Image: http://farm9.staticflickr.com/8241/86607...658a_c.jpg]
I'll let it cure for a week or two, then sand with 600 grit and spray on a couple more coats.
If I had to do it again, I would have gone a little bit lighter on the body. Maybe one or two less coats of the extra dark walnut.
[Image: http://farm9.staticflickr.com/8246/86607...3a8c_c.jpg]
(This post was last modified: 04-18-2013, 07:00 PM by Bob Andersen.)
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
WOW  
Bob, do you have any Mohawk No Blush Plus? It's great for getting rid of the blushing. Just spray a little on the area where the lacquer has blushed, and the blushing magically disappears!
--
Ron Ramirez
Ferdinand IN
Users browsing this thread: 4 Guest(s)
|
|
Recent Posts
|
|
Philco 91 Restore Code ??
|
| No, that cannot be the 47.
The 47 is a regular backelite block cap. Look at the chassis picture, it is shown there. Rig...morzh — 01:45 PM |
|
Philco 91 Restore Code ??
|
| I have changed the title of this thread from Philco 91 Schematic.
I have gone through most of the cap replacements. I...dconant — 01:26 PM |
|
462ron
|
| Here is an online transistor substitution site…
Ron462ron — 08:44 AM |
|
1930s Stewart-Warner Tombstone Radio need help identifying model number
|
|
One way to repair a broken wire on a coil is to take a copper strand out of some 18 gauge electrical cord, make a &quo...captainclock1988 — 12:55 AM |
|
B&K 1077B no video
|
| Hello Tim,
I once had a Jcpenny 13inch tv /monitor built by NEC come into my repairshop it would start acting up at tim...radiorich — 10:59 PM |
|
Restoring Philco 96
|
| Mike;
The last time I took a potted condenser can apart, and it was maybe 1/4 the size of the one in the model 96, I ...Arran — 10:56 PM |
|
Compatible crts
|
| Bob Andersen — 08:58 PM |
|
1930s Stewart-Warner Tombstone Radio need help identifying model number
|
| One way to repair a broken wire on a coil is to take a copper strand out of some 18 gauge electrical cord, make a "...Arran — 08:41 PM |
|
Restoring Philco 96
|
| Have just aligned it. Surprisingly, it was not that much off at all. Barely.
Aligning TRF sets is pure pleasue, as ther...morzh — 07:52 PM |
|
6TPZ and 5TPO Radio Help
|
| 1 - 0v - correct
2 - 0v - correct
3 - 0v - --------------------- both 3 and 4 should be the same. Check L2 for being ope...morzh — 05:15 PM |
|
Who's Online
|
There are currently 3620 online users. [Complete List]
» 3 Member(s) | 3617 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
