Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Ballast Tube
#1

I just got a GE radio with a ballast tube. I've never seen one(or heard of one) and was wondering how to test it.

I did some reading about it but couldn't find a test procedure. Any ideas?

Thanks,

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#2

What's the number of the ballast?
#3

It's a BL42B

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#4

Eric

You simply measure resistance between the pins where the resistors inside the tube are connected to.
It is that simple.
#5

These ballasts are available from several sources for about $12. Looking at the schematic, I see that pin 3 to pin 7 should show continuity. Pin 7 to pin 8 is the dial lamp connection. To check both sections check from pin 3 to pin 8, then from pin 8 to pin 7
#6

Thanks, B A, I'll check it out.

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#7

Well, you were right. No continuity at all. I opened it up just to see what it looked like and found broken wires inside. Has anyone put resistors inside the metal tube instead of replacing it?

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#8

B A, where did you see them advertised?

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org

#9

http://www.vacuumtubes.net/Prices%20Ballasts.htm
#10

Thank you. It will be ordered tomorrow.

Eric
The Villages, FL
Member: Philco Phorum, ARF, ARCI & Radiomuseum.org





Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Philco 91 Restore Code ??
Or you could just square the current :lol: As for the values, they are dependent on the 1 or 2-speaker system. The...morzh — 05:46 PM
Philco 91 Restore Code ??
If you know the fc resistance you can use 120 ma nominal current through the resistor to get the voltage drop then calcu...RodB — 05:21 PM
Philco 91 Restore Code ??
Thanks Mike. I at least know why it is there if I don't fully understand it. I see where you talk about a cap and resist...dconant — 04:49 PM
Philco 91 Restore Code ??
Well, this cap you showed cannot possibly, due to the way it is constructed, be 1000pF (0.001). It can be in tens of pF....morzh — 03:13 PM
Philco 91 Restore Code ??
I have two schematics for this radio one shows the 47 block (126-226) and the other (121-221) does not. My radio does no...dconant — 02:32 PM
Philco 91 Restore Code ??
No, that cannot be the 47. The 47 is a regular backelite block cap. Look at the chassis picture, it is shown there. Rig...morzh — 01:45 PM
Philco 91 Restore Code ??
I have changed the title of this thread from Philco 91 Schematic. I have gone through most of the cap replacements. I...dconant — 01:26 PM
462ron
Here is an online transistor substitution site… Ron462ron — 08:44 AM
1930s Stewart-Warner Tombstone Radio need help identifying model number
One way to repair a broken wire on a coil is to take a copper strand out of some 18 gauge electrical cord, make a &quo...captainclock1988 — 12:55 AM
B&K 1077B no video
Hello Tim, I once had a Jcpenny 13inch tv /monitor built by NEC come into my repairshop it would start acting up at tim...radiorich — 10:59 PM

[-]
Who's Online
There are currently 3070 online users. [Complete List]
» 4 Member(s) | 3066 Guest(s)
AvatarAvatarAvatarAvatar

>