Posts: 1,106
Threads: 88
Joined: Jun 2011
City: Tacoma
State, Province, Country: Washington
What would you call the chassis screws for this radio? 10-24? 10-32? Something else?
I had a repro cabinet made (will post pics soon) for my 89 (which I bought from Ron some time ago), but don't have any chassis screws that fit it. I bought some from Renovated Radio that were supposed to fit, but they do not. Perhaps I bought the small ones by mistage. That being said, I would prefer to get the right size and type of screw to complete this set.
Thank you for your time.
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
I *think* that #14 sheet metal screws, the kind with hex (bolt) heads, will work. They are just ever so slightly larger than the originals were, and have to be forced in the first time they are used, but after that they are fine. Pretty sure #14 is the correct size but it's early and the ol' brain is still just barely functioning at 5:30 am EDT...
Well, I just looked at the Renovated Radios page and I see the larger screws he carries are 1/4 x 1-1/2, which must be the right ones. Ed should know, he does a great job with those repro parts. I do recall the #12 is the right size for the 1939-42 and some 1935-36 models, as he states on the page.
--
Ron Ramirez
Ferdinand IN
Posts: 1,407
Threads: 72
Joined: Oct 2007
City: Linn Creek, MO
I think the original screws were a number 14. The diameter of a number 14 screw is .242 inch, so a 1/4 inch would be close.
Steve
M R Radios C M Tubes
Posts: 736
Threads: 26
Joined: Jun 2013
City: Hayward, California
Of course , i'm not an expert on these Radios...But considering how old it is and the fact that the US didn't take up metric until much later, the 1/4" screw would be my guess. Also, didn't Ron say the #14 would be a little tight at first? That tells me that the US size type would probably be correct as the US and Metrics sizes are inbetween each other.
(This post was last modified: 08-06-2013, 07:13 PM by Warren.)
Posts: 4,804
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
These are some sort of sheet metal screw, I don't know if they were standard or proprietary to Philco. Metric and SAE really only applies to machine screws, sheet metal ones are inbetween machine screws and wood screws in terms of thread pitch.
Regards
Arran
Posts: 736
Threads: 26
Joined: Jun 2013
City: Hayward, California
Yes, the threads are difinitely different than machine screws, But the thickness of the shafts are also different between metric an sae. Good Luck finding the right one.
Posts: 1,106
Threads: 88
Joined: Jun 2011
City: Tacoma
State, Province, Country: Washington
Like I said, that's why God invented our friend, the tap and die set.
Posts: 736
Threads: 26
Joined: Jun 2013
City: Hayward, California
Most Tap and Die sets are for machine screws , and also still in either metric or sae.... back to the same problem. 
Posts: 1,407
Threads: 72
Joined: Oct 2007
City: Linn Creek, MO
I would use the 1/4 inch diameter sheet metal screws, they will work just fine.
Steve
M R Radios C M Tubes
Users browsing this thread: 4 Guest(s)
|
|
Recent Posts
|
|
Philco 91 Schematic
|
| Hi Rod,
The resistor connects to pin 4 and the ungrounded side of block 9. From pin 9 of the RF tube to one side of ...dconant — 09:34 AM |
|
Just got a 49-1613 need to know...everything!
|
| I just found your post. I have this exact same model, and have had it since 1985 when I was 15 years old! I performed a ...MuzzcoVW — 09:11 AM |
|
B&K 1077B no video
|
| Hello Tim,
I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ?
Sincerely Richardradiorich — 01:55 AM |
|
B&K 1077B no video
|
| I found a schematic and think I have the problem traced down to the minus power supply. I have very low voltages that go...TV MAN — 12:41 AM |
|
RCA 15X
|
| I'd try replacing the bulb first and if that doesn't do it, then change the 35Z5 and see if the problem goes away.NostalgiaRadioTime — 12:28 AM |
|
B&K 1077B no video
|
| Hello Tim,
I have that exact unit in my shop too plus a Sencore unit there are times I like one or other !!.
Sincerely...radiorich — 11:07 PM |
|
RCA 15X
|
| Everthing goes at once, maybe it's the cold weather, I have had 2 dial strings break and no my little RCA is having dial...Paul Philco322 — 10:26 PM |
|
Philco 91 Schematic
|
| Hi Dan,
I can't explain this specific resistor but I have seen the use of a switch to apply B+ voltage to screen gri...RodB — 09:36 PM |
|
6TPZ and 5TPO Radio Help
|
| I suspect it's been repaired before.
And I suspect whoever repaired it, wanted to re-use old transistors' pin stubs in o...morzh — 09:24 PM |
|
B&K 1077B no video
|
| Thanks Rich! I'll take a look and see what he has. I know there's more modern equipment to be had, but this one I know a...TV MAN — 09:11 PM |
|
Who's Online
|
There are currently 8568 online users. [Complete List]
» 1 Member(s) | 8567 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
