Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Restoring a 39-7
#16

I prefer to keep rubber and wires separate. Icon_lol
#17

Thanks, I'll see if my local electronics shop has any...

Edit:

No luck. I have to go to the Internet. Any decent sources for these? I cannot locate any 6000pF caps, only 4700pF.

So what can I do? 4700 is enough, 10000 too much, or should I wire 3 2200's in parallel (I'd rather not tempt the fates of MTBF this way)?

Also there is one other silver mica capacitor in there - it's part 6A on the schematic. The problem is it's listed as a 20mfd device and there's no way this is 20mfd, it's just way too small. Elsewhere on the schematic it's listed as 20mmfd, which makes a lot more sense for this type of capacitor.
#18

It sings again!

After putting up with the repaired speaker that tended to muddle the sound and distort at medium-high volumes, I decided to take a closer look

The speaker was slowly disintegrating - small cracks were developing, and the most careful light touch caused the cone to split.

So I had the speaker reconed.

It's now a whole different radio. Plays loud, tight, and clear at all volumes.

I probably put more money I to this than I should, but it would have been a pity to leave it in such poor condition.

   
#19

Speaker looks very nice. Who did you send it to for reconing?
#20

The Speaker Shop:

http://thespeakershop.com
#21

Nice set! You've got the delux model with the brass escutcheon around the dial. Many years ago I had the chairside version of that set. Wish I hadn't sold it! Good player and very sensitive too.
Terry
#22

Actually, this one doesn't. It's pretty plain. I have a nearly identical model with the preset tuning buttons and the brass escutcheon though. You are right about the play quality and sensitivity though. A solid little radio. The guy who had it before me wrote 38-12 on the chassis, but it is a 39-6 as far as I can tell.

Edit: no, it isn't, it *is* a 38-12 chassis. Just double-checked the schematic. Someone put a dial from a 39-6 on it and stuck it in a 39-6 cabinet. >:-(

Aw crap! Just noticed I posted about the the speaker in my 39-7 thread. At least the 39-7 is a real one.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
Gloritone 27 Radio
I have a model 27 that someone painted the cabinet brown. I've been trying to sell it for awhile but the cabinet paint m...Jim Dutridge — 02:30 PM
Restoring Philco 96
Joseph Yeah. The situaction is complicated by me living with my family in NJ while mom is in FL. Were it not for my ...morzh — 10:55 AM
Restoring Philco 96
Best of wishes for your mother. I hope she recovers well. My mother struggles with sciatic pain as well, so I am familia...jrblasde — 10:41 AM
Restoring Philco 96
Well, because I am away, I cannot check it. Hope mom becomes better enough for me to get back. I think I will be here f...morzh — 10:27 AM
Restoring Philco 96
Nice find! I hope it completes your console.jrblasde — 08:45 AM
Gloritone 27 Radio
Hello john, That, is the first time I have have seen or heard of that brand and model. Welcome to the party !! Sincer...radiorich — 08:08 AM
370 Norman Bel Geddes trim pieces
Thank you! I’ll probably use the half-round molding and tone it to match the original. Thanks for the replies!Max T — 06:34 AM
Gloritone 27 Radio
I'm kind of late to this thread, but Buzz1151 has a 3 part restore series on the model 27: A little bit of extra t...Eliot Ness — 05:48 AM
370 Norman Bel Geddes trim pieces
You can get half-round moulding in various diameters at any home improvement store. That way the flat edge is uniform. ...GarySP — 12:03 AM
42-345 Resistors
Great comments. I have a tinkering bench at my office, and that's where Little Phil is right now. I will have to comb ...proftrussell — 11:12 PM

[-]
Who's Online
There are currently no members online.

>