Posts: 4,804
Threads: 54
Joined: Sep 2008
City: Sandwick, BC, CA
The control may or may not have to be unsoldered to remove it from the chassis, but it probably will unless there is a lot of slack in the wiring. The usual trick was to solder a jumper between one side of the switch and the bottom end of the pot using that as the tie point for common negative, so the two will have to disconnected from one another. Depending on how it is constructed you will have to unbend the tabs on the front of the control to get the cover off to get at the tabs that hold the switch on, that is if the switch has to be replaced.
If you are lucky you may be able to take the cover for the pot off, and with the switch still attached, soak it in some solvents to dissolve the crud inside the switch to free it up and clean the contacts. If you are less lucky you may have to strip it down further, remove the switch section from the control cover to gain better access to the internals, which is not something you want to do if working on small mechanical things is not your forte. If you are unlucky it will be broken inside, or the switch contacts will be burned and no amount of cleaning will fix it.
Regards
Arran
Posts: 16,213
Threads: 562
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
I think it is not crud. I exhibits zero cinductivity. After multiple attempts. Which to me means the contacts do not even touch.
With od Philco switches like 20/70/90/111 type bad contact is common but there is nevertheless a contact, and once it conducts, it self-heals.
This type has no contact whatsoever.
Buying a new working part is easier and with this situation the money saved is not worth the effort.
Posts: 16,213
Threads: 562
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
The pot came today, NOS, 6 bucks....what beats this?
I was afraid of desoldering stuff so not to ruin wire, but Radio Gods smiled at me today and no wires lost insulation. I replaced just one wire - looked a bit chewed up after me handling it with needlenose and soldering iron.
Now all works like it should.
Took me about under 1/2 hr.
Posts: 4,106
Threads: 310
Joined: Nov 2013
City: Kings Park NY
Good work! 
I was gonna scratch your cabinet if the job was incomplete. 
Cant wait to meet up. next, next weekend with you and Sam.
Bring a cabinet so I can pawn some more chassis off on you to repair.
You know you want to tackle that Silvertone 45! 
Kirk
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 2,353
Threads: 92
Joined: May 2010
City: Clayton, NC
Kirk, you ought to see about getting your model 16X working properly. They are a very good radio!!!
Posts: 16,213
Threads: 562
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Anything that has 16 in it is
37-116, 116x, 16 etc.
Posts: 4,106
Threads: 310
Joined: Nov 2013
City: Kings Park NY
supposedly it was redone a few years ago but I havent opened it.
I opened the G500 Zenie I got from the same guy and OMG it was a terrible resto underneath. he just touched and soldered the wires. there was a resistor just sitting on the bottom of the cabinet and 2 wires disconnected.
So I cant wait to see the 16 underneath.
I have too many radios open right now so it will have to wait if I keep it. I dont think I have room for it and it has been on Craigslist for a week or 2 and no bites at $125.00 
Gosh I need my house back...
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 16,213
Threads: 562
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
You need it back - I need a new one - this one does not have any good place to put the measly 16 radios I got.
Let alone the kind of collection Russ got in his place. 
Posts: 4,106
Threads: 310
Joined: Nov 2013
City: Kings Park NY
If you can fit it in your car with Sams 38-3, it's yours Mike
I may just have a chassis or four for you anyway,
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Posts: 16,213
Threads: 562
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Posts: 16,213
Threads: 562
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Fixed the power switch in the volu.e pot. Was really oxidized. Then lubed the pot. Will keep as a spare.
Posts: 4,106
Threads: 310
Joined: Nov 2013
City: Kings Park NY
Times I have been electrocuted in 2021
As of 1/01/2021
AC: 4 DC: 1
Last year: 6
Users browsing this thread: 9 Guest(s)
|
|
Recent Posts
|
|
1930s Stewart-Warner Tombstone Radio need help identifying model number
|
| UPDATE: I was able to pick up a signal generator on the cheap (amazingly enough) on feebay and I did an IF alignment fol...captainclock1988 — 09:53 AM |
|
Philco 91 Schematic
|
| Hi Rod,
The resistor connects to pin 4 and the ungrounded side of block 9. From pin 9 of the RF tube to one side of ...dconant — 09:34 AM |
|
Just got a 49-1613 need to know...everything!
|
| I just found your post. I have this exact same model, and have had it since 1985 when I was 15 years old! I performed a ...MuzzcoVW — 09:11 AM |
|
B&K 1077B no video
|
| Hello Tim,
I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ?
Sincerely Richardradiorich — 01:55 AM |
|
B&K 1077B no video
|
| I found a schematic and think I have the problem traced down to the minus power supply. I have very low voltages that go...TV MAN — 12:41 AM |
|
RCA 15X
|
| I'd try replacing the bulb first and if that doesn't do it, then change the 35Z5 and see if the problem goes away.NostalgiaRadioTime — 12:28 AM |
|
B&K 1077B no video
|
| Hello Tim,
I have that exact unit in my shop too plus a Sencore unit there are times I like one or other !!.
Sincerely...radiorich — 11:07 PM |
|
RCA 15X
|
| Everthing goes at once, maybe it's the cold weather, I have had 2 dial strings break and no my little RCA is having dial...Paul Philco322 — 10:26 PM |
|
Philco 91 Schematic
|
| Hi Dan,
I can't explain this specific resistor but I have seen the use of a switch to apply B+ voltage to screen gri...RodB — 09:36 PM |
|
6TPZ and 5TPO Radio Help
|
| I suspect it's been repaired before.
And I suspect whoever repaired it, wanted to re-use old transistors' pin stubs in o...morzh — 09:24 PM |
|
Who's Online
|
There are currently 7542 online users. [Complete List]
» 4 Member(s) | 7538 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
