Posts: 133
Threads: 27
Joined: Aug 2006
City: Roseville,Ca.
good afternoon everybody. i have come closer to my goal of collecting the entire 1936 philco line up today with a purchase of a 660 in near virginal condition and still working,even with the original filters which i will remedy shortly.
it plays well on all bands so no electrical issues are holding me up,i will replace critical caps that will cause damage in case of failure and of course any bad resistors but i will attempt to leave it as original as possible.
BUT! i have a mechanical issue. the dialscale isn't keeping up with the tuning cap,the mounting flange for the scale has some slop in it so it doesn't move evenly with the tuner. the vernier has been cleaned and lubed. how do i get the slop out so the scale tracks correctly with the tuner?
this is the same dialdrive as the 116x which i have that has the same problem.
thanks,phil
Posts: 1,703
Threads: 55
Joined: Sep 2005
City: Evanston, IL
Posts: 133
Threads: 27
Joined: Aug 2006
City: Roseville,Ca.
hi chuck and thanks for the response.
the venier/speed controls are working fine,the slack is in the plate/hub that the dialscale mounts to so just the scale is sloppy,not the tuner's drive. will this fix that?
phil
Posts: 133
Threads: 27
Joined: Aug 2006
City: Roseville,Ca.
does anyone know how to remove the mounting hub for the scale????
phil
Posts: 893
Threads: 9
Joined: Mar 2008
City: Vieques, PR USA
State, Province, Country: PR
If its like my 630 there is a split washer type thingie on the front of the hub. It twists 90 degrees for removal. You can use needlenose pliers as a tool.
(Note from site admin: Sorry, but the photo which was attached to this post is no longer available.)
Posts: 133
Threads: 27
Joined: Aug 2006
City: Roseville,Ca.
hi exray,i have that off,i need to remove the hub behind it,my scale is slipping-not the tuner.
phil
Posts: 133
Threads: 27
Joined: Aug 2006
City: Roseville,Ca.
is this question beyond everyone or is it no one is here?
phil
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
Have you checked the setscrew on the semi-circular ring hub that drives the tuning mechanism to make sure it is tight?
--
Ron Ramirez
Ferdinand IN
Posts: 133
Threads: 27
Joined: Aug 2006
City: Roseville,Ca.
hi ron,yeah it's fine.
the tuner drive has absolutely no play-nada-it's just the hub for the dialscale that slips.
phil
Posts: 13,776
Threads: 580
Joined: Sep 2005
City: Ferdinand
State, Province, Country: Indiana
That setscrew on the semi-circular ring hub also holds the dial scale hub in place. It can wear out and allow the dial scale to slip. I had that happen to a 116 once (same dial drive mechanism). Never could get it fixed. But don't let that dissuade you - there must be a way...
--
Ron Ramirez
Ferdinand IN
Posts: 119
Threads: 5
Joined: Mar 2006
City: Coram, N.Y. 11727
philco phan, any possability you could post a few pictures, different aspects, so some of us not formiliar with set could try to help? PL
Posts: 133
Threads: 27
Joined: Aug 2006
City: Roseville,Ca.
pics are in this arf thread,thanks,phil
<!-- m --><a class="postlink" href="http://www.antiqueradios.com/forums/viewtopic.php?t=106409" onclick="window.open(this.href);return false;">http://www.antiqueradios.com/forums/vie ... p?t=106409</a><!-- m -->
Posts: 133
Threads: 27
Joined: Aug 2006
City: Roseville,Ca.
SUCCESS!!
i loosened the set screws and gently tapped the entire mechanism further onto the shaft-maybe 1/16 inch and retorqued the screws and no more slop!!! it moves perfectly!!
thanks to all that helped,phil
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
6TPZ and 5TPO Radio Help
|
| Thanks, will do.R3Sons — 01:25 PM |
|
1930s Stewart-Warner Tombstone Radio need help identifying model number
|
| UPDATE: I was able to pick up a signal generator on the cheap (amazingly enough) on feebay and I did an IF alignment fol...captainclock1988 — 09:53 AM |
|
Philco 91 Schematic
|
| Hi Rod,
The resistor connects to pin 4 and the ungrounded side of block 9. From pin 9 of the RF tube to one side of ...dconant — 09:34 AM |
|
Just got a 49-1613 need to know...everything!
|
| I just found your post. I have this exact same model, and have had it since 1985 when I was 15 years old! I performed a ...MuzzcoVW — 09:11 AM |
|
B&K 1077B no video
|
| Hello Tim,
I would if it's a leaky Capacitor So are all 3 of those B- voltages low then ?
Sincerely Richardradiorich — 01:55 AM |
|
B&K 1077B no video
|
| I found a schematic and think I have the problem traced down to the minus power supply. I have very low voltages that go...TV MAN — 12:41 AM |
|
RCA 15X
|
| I'd try replacing the bulb first and if that doesn't do it, then change the 35Z5 and see if the problem goes away.NostalgiaRadioTime — 12:28 AM |
|
B&K 1077B no video
|
| Hello Tim,
I have that exact unit in my shop too plus a Sencore unit there are times I like one or other !!.
Sincerely...radiorich — 11:07 PM |
|
RCA 15X
|
| Everthing goes at once, maybe it's the cold weather, I have had 2 dial strings break and no my little RCA is having dial...Paul Philco322 — 10:26 PM |
|
Philco 91 Schematic
|
| Hi Dan,
I can't explain this specific resistor but I have seen the use of a switch to apply B+ voltage to screen gri...RodB — 09:36 PM |
|
Who's Online
|
There are currently 3958 online users. [Complete List]
» 1 Member(s) | 3957 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
