Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

37-650 fading performance
#1

The 37-650 I have starts up fine and strong but fairly soon (5 min or less) starts to "fade out" to low volume. I have to turn the volume pot to almost max to get "normal volume".

If I touch or even get close to the grid cap of the 6K7 tube that attaches to the tuning cap I get full volume to return. I've swapped out the 6K7 tube but get the same results.

Any suggestions on where to start looking? Output tubes getting gassy as they heat up?
#2

I doubt its the output tubes. If the volume returns when you touch the cap of the RF amp 6K7, then it probably not related to the output stage. Does the B+ power supply voltage change when the problem occurs? Gassy outputs would make the B+ voltage drop noticeably.

Sounds like it might be related to the AVC circuit which controls the negative DC bias voltage on the 6K7 grid. This AVC circuit is also connected to the 6A8 and the 6K7 IF amp, so I would also try replacing these with known good ones.

You can also check the resistors marked 7 and 34 on the schematic and see if they have increased significantly in resistance.
#3

What's your oscillator voltage doing? Is it going down until you touch the grid cap?
(I am assuming it's not de-tuning itself...that is, turning the tuning knob does not bring back full volume.)

Rob
#4

I had the same problem, happened to be the 75 tube.
Can be any tube, can be other reasons, but I would replace the tubes one by one.

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#5

(09-18-2017, 06:44 PM)robsradioactive Wrote:  What's your oscillator voltage doing? Is it going down until you touch the grid cap?
(I am assuming it's not de-tuning itself...that is, turning the tuning knob does not bring back full volume.)

Rob

Actually. If I could stand there with my finger on the grid cap all day I'd have a perfect playing set. Icon_smile
#6

(09-19-2017, 09:08 AM)Tgace459 Wrote:  Actually. If I could stand there with my finger on the grid cap all day I'd have a perfect playing set. Icon_smile

Might be worth it Icon_lol

People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
#7

Clip a gator wire from the grid cap to your long wire antenna and you can get your finger back! Icon_lol

Greg V.
West Bend, WI
Member WARCI.org
#8

heehee
#9

Hmmm...AM was fading but AUX input was working fine. Now even the AUX is faded out to almost static.

I'm gonna have to pull the chassis and take a look.




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
An attempt to remove the Field Coil from a G speaker
Paul, thanks, Anything can help. Gary Thanks, lemme look! PS. Looked it up. They have kits and parts for mod...morzh — 02:45 PM
An attempt to remove the Field Coil from a G speaker
Paul, thanks, Anything can help. Gary Thanks, lemme look!morzh — 02:39 PM
46-1201 Trip Switch Spring
I deleted the other thread, as it was duplicate and did not have the photo. Please proceed with this one.morzh — 02:37 PM
46-1201 Trip Switch Spring
Hello, first post here, bear with me. I've been electronically refurbishing a 46-1201 that I received from a relative. ...ConcernedFeller — 01:46 PM
An attempt to remove the Field Coil from a G speaker
I am late to this post, amazing amount of work for a speaker Mike. You must like the challenge. I have a speaker from an...Paul Philco322 — 01:04 PM
An attempt to remove the Field Coil from a G speaker
Mike, give this site a look for your spider. Can't hurt. Take care and BE HEALTHY! -GaryGarySP — 12:41 PM
An attempt to remove the Field Coil from a G speaker
Rod, Bubble packaging? The one I know (if you mean the large bubble type) is really thin. I have some at home. Is there...morzh — 12:23 PM
An attempt to remove the Field Coil from a G speaker
Q8. What's the meaning of life? I have read that someone made a spider out of the clear plastic from bubble packagin...RodB — 11:07 AM
An attempt to remove the Field Coil from a G speaker
So, Q1. Does anyone know where to get the spider. Q2. If there is no such place, what material is best? I doubt tin is...morzh — 09:43 PM
An attempt to remove the Field Coil from a G speaker
Arran The oxidation seems to go deep, a few layers. The break starts right there, but then it will occur on every la...morzh — 07:35 PM

[-]
Who's Online
There are currently 7750 online users. [Complete List]
» 1 Member(s) | 7749 Guest(s)
Avatar

>