Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
I think I'm missing something here. I'm feeding a 455Hz signal in to troubleshoot. I get a good strong signal to the voulme control, and also on the top of C424 (.006mfd). But I get nothing on the top side of R419 right above it. Resistor ohms out just fine. Anyone lead me in the right direction? I hope this schematic is readable. Thanks.
[img] [Image: http://i1367.photobucket.com/albums/r796...jhkvn7.png][/img]
Posts: 16,306
Threads: 569
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
C423 shorted?
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
(09-03-2018, 05:07 PM)morzh Wrote: R423 shorted?
Did you mean C423?
Posts: 16,306
Threads: 569
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Yes, I did.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
No, C423 is O.K. I just checked it even though it's new.
Posts: 7,294
Threads: 268
Joined: Dec 2009
City: Roslyn Pa
I'm missing something too. If you apply a rf signal to the volume control you shouldn't hear it. The rf signal must be rectified to covert it to an audio signal. If you want the use rf @ 455kc connect it to the control grid of the 7H7 (p6 I think). Make sure your mode switch is good and clean.
When my pals were reading comic books
I was down in the basement in my dad's
workshop. Perusing his Sam's Photofoacts
Vol 1-50 admiring the old set and trying to
figure out what all those squiggly meant.
Circa 1966
Now I think I've got!
Terry
(This post was last modified: 09-03-2018, 08:38 PM by Radioroslyn.)
Posts: 16,306
Threads: 569
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
What I did not appreciate was it was 455kHz. C423 simply shorts it.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
(09-03-2018, 08:37 PM)Radioroslyn Wrote: I'm missing something too. If you apply a rf signal to the volume control you shouldn't hear it. The rf signal must be rectified to covert it to an audio signal. If you want the use rf @ 455kc connect it to the control grid of the 7H7 (p6 I think). Make sure your mode switch is good and clean.
I'm using an Eico 324 RF generator with internal modulation AF out, not a strict RF signal. I just finished recapping the chassis and am in the process of alignment. Guess I should have explained that. Sorry. I'm working backwards from the amp section to find out why I'm not getting audio.
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
(09-03-2018, 08:59 PM)morzh Wrote: What I did not appreciate was it was 455kHz. C423 simply shorts it.
It's AF modulated RF. I used to use a "Mosquito" for tracing. Remember those?
Posts: 1,824
Threads: 114
Joined: Jul 2014
City: Sneedville, TN
I restored a 48-482 back in 2014. The toughest part was aligning the FM converter, but it can be done using a regular modulated sig gen if you carefully follow the instructions in the Philco service paperwork, it tells this alternate method. You may find my thread on this project of use. http://www.philcoradio.com/phorum/showth...?tid=10134
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
Read through your thread. Might be some useful information there if I ever get through the BC part.
Posts: 16,306
Threads: 569
Joined: Oct 2011
City: Jackson
State, Province, Country: NJ
Patrick
Where exactly is it that you feed the IF signal to?
I am still not sure.
People who do not drink, do not smoke, do not eat red meat will one day feel really stupid lying there and dying from nothing.
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
(09-04-2018, 08:46 AM)morzh Wrote: Patrick
Where exactly is it that you feed the IF signal to?
I am still not sure.
I took a step back, and used the Philco troubleshooting guide. I have a strong IF signal at the grid of the 1st IF amp. I have only a very weak signal at the plate of the converter. That would indicate a problem at the 1st IF transformer, Z400. So it appears the problem most likely is there, and I was just going off on a tangent somewhere.
Posts: 365
Threads: 76
Joined: Oct 2014
City: Winter Haven, FL
Found the problem! Z404, a choke/cap combination, was wired to the white lead on Z400 instead of the green lead. The two connection points are right next to each other. That caused a very weak signal from the plate of the converter. Connected it properly, aligned the IF, and picks up stations. I really think the stock speaker is too small for this radio.
Users browsing this thread: 1 Guest(s)
|
|
Recent Posts
|
|
Philco model 60
|
| Yes I was there. I got some real bargains there. Plus a Zenith 7G605 clipper that I have been trying to find for a fair ...Radios1340 — 01:46 PM |
|
The speaker table error?
|
|
G 10-1/2" 65, 76, 87, 95
Push-Pull 45's
2766
0.7
550
3200
H 10-1/2" 77, 96
Push-Pull...morzh — 09:26 PM |
|
A Marconi model 86
|
| I have a Stromberg, one of the early ones, seems early 30s.
This is what I call a back breaker. None of the early Philc...morzh — 08:28 PM |
|
A Marconi model 86
|
| A backbreaker.....PaulPaul Philco322 — 08:12 PM |
|
A Marconi model 86
|
| >>What a behemoth!
A Juggernaut.morzh — 07:47 PM |
|
Philco 70 antenna lead
|
| I am not sure I understood about the coils and the mush. I looked an more than one coil in 20, 70, 90, 60, Zeniths and ...morzh — 07:46 PM |
|
A Marconi model 86
|
| :e_biggrin: What a behemoth! I hope the final result is as much a quality sounding example! Keep us posted on your pro...GarySP — 07:32 PM |
|
A Marconi model 86
|
| I should add that the double conversion may only be used on the shortwave bands, but I haven't looked at the schematic t...Arran — 07:27 PM |
|
Philco 70 antenna lead
|
| Yes, that wire will not pick up much interference as routed - the RF at that level won't be affected, and if you have st...radio1 — 07:26 PM |
|
Philco model 60
|
| I'm also a member of MARC. Did you attend the Vintage Electronics Expo in Waterford, MI last month? That's where I got...GarySP — 07:22 PM |
|
Who's Online
|
There are currently 6756 online users. [Complete List]
» 2 Member(s) | 6754 Guest(s)
|
|
|
|
 
|
![[-]](https://philcoradio.com/phorum/images/bootbb/collapse.png "[-]")
