1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration

Welcome Guest! Be sure you know and follow the Phorum Rules before posting. Thank you and Enjoy! (January 12) x

Thread Closed
Thread Rating:
  • 0 Vote(s) - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5

Threaded Mode
OK, you guys were right, again
DKinYORKpa
Member
***
Posts: 193
Threads: 50
Joined: Oct 2011
City: York PA
#1

01-20-2013, 01:08 PM
The tube socket for the 80 tube was bad on my Philco 18. So for curiosity sake, after I removed the socket I removed the rivets holding the 2 wafers together and inside between the 2 high voltage lugs was a nice pile of burnt residue. When I meter from one lug to the pile black stuff, I have continuity! Thus the short, as you warned me. Now, I removed a socket from a donor non-Philco chassis. It's the type that has "80" imprinted on the top, three wafers with a rivet in the center. Having never encountered this issue before, I'm inclined to use this socket. Comments?
Find
codefox1
Silent Key
*****
Posts: 2,128
Threads: 18
Joined: Oct 2008
City: Merrick, Long Island, NY
#2

01-20-2013, 01:50 PM
Probably OK, but I'd rather get good quality new porcelain socket that would fit the existing cutout. Measure and post a WTB in classifieds. Someone may just contribute to you for postage only.
Find
DKinYORKpa
Member
***
Posts: 193
Threads: 50
Joined: Oct 2011
City: York PA
#3

01-20-2013, 03:02 PM
You're probably right, but I made the swap. Seems fine. Thanks.
Find
« Next Oldest | Next Newest »
Thread Closed




Users browsing this thread: 1 Guest(s)
[-]
Recent Posts
An attempt to remove the Field Coil from a G speaker
Gary I in fact did, on a 38-14, I think, where I had a speaker with the dead coil. Well...it kinda worked. Kinda, be...morzh — 10:38 PM
An attempt to remove the Field Coil from a G speaker
Mike, what ever happened to that plan you had to try using a rare earth magnet to magnetize the pole? This looks like a...GarySP — 10:25 PM
RCA T62 is playing.....
Beautiful set.morzh — 09:07 PM
An attempt to remove the Field Coil from a G speaker
Well....here it is. The green stuff. Unfortunately, probably penetrates deep. I opened the top layer and saw that: ...morzh — 08:58 PM
Philco 91 Restore Code ??
:clap: :clap: :clap: :clap: Really nice workmanship!!! Top of the chassis looks great. Sorry about the long winded e...MrFixr55 — 08:09 PM
Philco 40-120C Restoration
Thank you for your reply. I will check voltages on the other tubes, look at resistor 23 and cap 25, etc. If all else fai...bluecap — 07:58 PM
RCA T62 is playing.....
Nice looking set great save. DavidDavid — 07:48 PM
Philco 89 indicator light.
Hello Jim, I have done several 89s. The trick is to move the drum in or out on it's shaft. You will need to loosen a set...dconant — 07:36 PM
An attempt to remove the Field Coil from a G speaker
MrFixr Yes, it is my plan to go with 45rpm spider if I go that far. No, the pole was not left-handed as I unscrewed ...morzh — 07:14 PM
Philco 40-120C Restoration
Change the tube. Check the tube's bias network. Are any other tubes experience the drop or just this?` Is resistor 23 OK...morzh — 07:09 PM

[-]
Who's Online
There are currently no members online.

>
  1. The PHILCO Phorum
  2. Philco Radio Discussions
  3. Philco Electronic Restoration